Help us keep the list up to date and Submit new DVD and Blu-ray Players here. This list is based from user reports and we have not verified or tested any region codes. Use them at your own risk.

What are Blu-ray and DVD region codes, country codes, multi-region or zone locks? Read DVD Player region codes and Blu-ray region codes.

Search DVD Player:  
Hits per page:


DVD Player Hacks Updated Add
Sony DVP-NS76H

5 user region code comments

September 09, 2021 Post region code/hack comment
PostRegion code hack posted by MARK Y -MARK, June 07 2006:


HI , I CAN CONFIRM THIS PLAYER IS AS EASY AS 1.2.3.4.5. I HAVE JUST DONE MINE !! -WITH THE USUAL SONY REMOTE CONTROL HACK ,JUST PROGRAM A ONE FOR ALL 4 .THE SAME AS ANY OTHER PLAYER HACK WITH DVP-NS IN FRONT OF IT ;
THEN TURN DVD PLAYER OFF ( STANDBY ) POINT AND PRESS 1.2.3.4.5.... SUCCESS SCROLLS ALONG ...MULTI-REGION IN SECONDS ! ALL DONE .



PostRegion code hack posted by Kenobiitti, January 28 2007:


This works also with DVP-NS76H
Hi Guys.

I have managed to hack my DVP-NS76H using a 3320 Nokia phone, on which I have installed the following software:
http://www.psiloc.com/?id=prod&nrp=97

This is a great little program that turn your phone in a programable remote control, using its IRda port !!

Once this was installed, I have transferefd to the phone the region hacks found at the below link:
http://www.avforums.com/forums/showthread.php?t=125063&highlight=DVP-NS430

The phone will recognise the ccf file and the remote control program will automaticaly start.

I wasn't able to attach commands to remote keys. So I had to send every command idividually by selecting send command from the menu. That is little confusing because all commands from 1-5 are unnamed and in backward order (from 5 to 1).

Turn of the dvd - no disk in the drive and send commands:
11 22 33 44 55 . so each command twice.

The dvd will power on. Repeat the proceduce and you have a multi region dvd player.

I'm not sure if it absolutely necessary to repeat the procedure, since my player was region free after first set of commands.

This hack can be found from several places, I didn't in vent it.




PostRegion code hack posted by barthabas, February 25 2007:


I successfully applied the Hack below posted by Ross on my DVP-NS76H. I tried the Laptop-IR hacks, couldn't get it to work. I had no kameleon 1 for All remote control, but I took my DVP to a shop which sells kameleons; they let me apply this hack (the DVP-NS76H does NOT display 'success'):

Region code hack posted by Ross, November 16 2003:
You might also like to try this method, which worked for my NS-300, if you have a One4all remote control. This is quoted from http://www.regionfreedvd.net/player/sony.html

--

I used oneforall kameleon remote to make my ns705 region free. just follow these steps:

prepare:
1. select dvd device on remote
2. hold magic button until rabbit comes out
3. enter device code 0533

program buttons 1..5 with the following codes:
1 - 189
2 - 255
3 - 095
4 - 221
5 - 079

1. hold magic button until rabbit comes out
2. press 994
3. press magic
4. enter 3digit code from above
5. press button (1..5) where to program it
6. repeat steps 1 to 5 for all keys.

have it a go:
1. remove disk, put player on standby
2. press 1,2,3,4,5 - success is displayed and player starts up
3. press 1,2,3,4,5 - player shuts down and BINGO!

should work for most of the dvp-ns### players"

--

I used a different One4all and it worked fine on the first attempt. The LED flashes twice on other One4all remotes instead of the rabbt appearing. Hope this helps.

Ross




PostRegion code hack posted by Sloth, May 07 2007:


This was done with a standard 0ne4All remote however, this hack will only work if you have a 'DVD' button on the remote. (I used URC-7730)

1.Turn off the DVD player. (The DVP-NS76H has no standby mode, so will turn itself off completely)

2.Select 'DVD' device on remote.

3.Hold 'MAGIC' button until red light blinks twice.

4.Enter the Sony device code 0533. The remote will now be able to control the DVD player.

5.Now you have to program buttons 1 to 5 with the following codes:(These codes will override the chip in the DVD player making it Multi-region)

1)00189
2)00255
3)00095
4)00221
5)00079

4.Firstly Hold 'MAGIC' button until red light blinks twice.

5.Type 994. (This will tell the controller you are programming individual buttons)The red light blinks twice again.

6.Press 'MAGIC' again. The red light will blink once

7.Enter one of the 5 digit codes from above followed by the button number you are assaining it to(eg MAGIC + 00189 + 1) The red light blinks twice.

8.NB. YOU MUST REPEAT STEP 4-6 BEFORE YOU TYPE IN EVERY CODE .

9.After all codes have been entered (1-5), with the DVD player off, Press 1,2,3,4,5 on the One4All remote and the DVD player should start up and the word "SUCCESS" scrolls along the display window.

10.I didn't have to but you can Press 1,2,3,4,5 - and the player shuts down and now works fine on any region code!

NB.Some older One4All remotes may accept only three codes: in that case remove the two leading 00's.

Enoy
D





PostRegion code hack posted by Sonia, September 09 2021:


Hi please help me and make my DVD
multiregion




1 DVD Hack hits, Showing 1 to 1 DVD Hacks
   

New hacks = New region code/hack comments since your last visit. Visit our sponsors! Try DVDFab and backup Blu-rays!
Search   Contact us   Privacy Policy   About   Advertise   Forum   RSS Feeds   Statistics   Software   

Site layout: Default Classic Blue

Affiliates: free-codecs.com

©1999-2024 videohelp.com